Turbo - Headers - Wastegate - Collectors - Mufflers - H-pipe
11-15-2006 | 09:56 AM
#1
Thread Starter
CMOC Rookie
Joined: Oct 2004
Posts: 328
From: Newcastle, Ontario
Turbo - Headers - Wastegate - Collectors - Mufflers - H-pipe
Hreaders - MAC 1 3/4 Shorties Ceramic coated - Almost new. They were bolted on to my car and ran for about 2 hours but I have decided to go with a new hotside kit to clear up some room.
NOTE: On one header the top of the flange was ground down about 1/8 of an inch to clear my valve cover (see picture)
$250.00 OBO
Wastegate - Turbonetics Deltagate II - Good to 450 WHP. Its small for my setup and the new hotside has adifferent flamge so its for sale. Spring is set for 9 PSI
$150.00 OBO
Collectors - Headman 1 3/4 Primary to 3" slip on. New and un-used. The surface rust you see wipes off with a rag and some cleaner, its just from sitting.
$50.00 OBO
Muffler - Dynomax Race Bullets - New and unused. Straight through design.
Innovative 68mm T04S Turbo - Turbonetics hot side, Garrett compressor. 68mm .55 trim .96 A/R Exhaust P trim. This will spool fast on a 302 and make up to 28 PSI. Efficency range on a 302 is 12-17 PSI. Turbo is tight, no shaft play, no dings on the blades. This made 472 RWHP and 620 TQ though an AOD. I am going bigger is the only reason for selling.
$700 OBO
79-93 H-pipe $150.00. It has lots of greasy fingerprints on it but it has never been installed. The crossover was never welded, like new.
NOTE: On one header the top of the flange was ground down about 1/8 of an inch to clear my valve cover (see picture)
$250.00 OBO
Wastegate - Turbonetics Deltagate II - Good to 450 WHP. Its small for my setup and the new hotside has adifferent flamge so its for sale. Spring is set for 9 PSI
$150.00 OBO
Collectors - Headman 1 3/4 Primary to 3" slip on. New and un-used. The surface rust you see wipes off with a rag and some cleaner, its just from sitting.
$50.00 OBO
Muffler - Dynomax Race Bullets - New and unused. Straight through design.
Innovative 68mm T04S Turbo - Turbonetics hot side, Garrett compressor. 68mm .55 trim .96 A/R Exhaust P trim. This will spool fast on a 302 and make up to 28 PSI. Efficency range on a 302 is 12-17 PSI. Turbo is tight, no shaft play, no dings on the blades. This made 472 RWHP and 620 TQ though an AOD. I am going bigger is the only reason for selling.
$700 OBO
79-93 H-pipe $150.00. It has lots of greasy fingerprints on it but it has never been installed. The crossover was never welded, like new.
11-15-2006 | 12:36 PM
#3
CMOC Rookie
Joined: Aug 2006
Posts: 121
From: hamilton
The H pipe in the picture is for long tubes 
11-16-2006 | 06:08 AM
#6
Thread Starter
CMOC Rookie
Joined: Oct 2004
Posts: 328
From: Newcastle, Ontario
yes the h-pipe is for LT's, I have had i in the garage for a few years but I ended up using some 3" for the exhaust. I would like 50.00 for the mufflers, there non chambered and are good for turbo setup's. I bought a new hot side that came with headers so I dont need the 1 3/4's any more.
08-08-2010 | 02:29 PM
#7
CMOC Newbie
Joined: Aug 2010
Posts: 12
From: winnipeg
you want 700.00 for turbo and piping headers complet.thx
08-08-2010 | 03:00 PM
#8
Adminut
Joined: May 2009
Posts: 5,722
From: Maple Tree, Branch #2 above the rope swing
Four year old ad, and Speedtospare hasn't logged on since February 2009. Glutton for punishment?
09-29-2010 | 06:55 PM
#9
Thread Starter
CMOC Rookie
Joined: Oct 2004
Posts: 328
From: Newcastle, Ontario
11-19-2010 | 07:23 PM
#10
CMOC Newbie
Joined: Nov 2010
Posts: 3
From: embrun, ontario
do you still have everything ... lookin for a turbo kit whats a price for everything and would i be able to bolt and go...
Thread
Thread Starter
Forum
Replies
Last Post
