Canadian Mustang Owners Club - Ford Mustang Forums
2012 11 22 MUSTANG 5.0
2012 11 22 MUSTANG 5.0
0 2012/11/22 17:42:29
2012 11 22 MUSTANG 5.0
2012 11 22 MUSTANG 5.0
0 2012/11/22 17:42:29
2012 11 22
2012 11 22
0 2012/11/22 17:42:29
2012 11 22
2012 11 22
0 2012/11/22 17:40:31
2012 11 21
2012 11 21
0 2012/11/22 17:40:31
Rear end after flush, buffed and painted
Rear end after flush, buffed and painted
0 2010/07/02 21:24:26
0 2010/07/02 21:24:26
10 hrs each rim method of 3 steps of sanding and polishing
10 hrs each rim method of 3 steps of sanding and polishing
0 2010/07/01 23:08:48
Rear end before flush
Rear end before flush
0 2010/07/01 23:08:48
Rims before
Rims before
0 2010/07/01 23:08:48
Flushed transmission fluid, power steering fluid and rear end fluid with friction modifier added
Flushed transmission fluid, power steering fluid and rear end fluid with friction modifier added
0 2010/07/01 23:05:27
Installed
Installed
0 2010/07/01 23:05:27
After 22 hrs of sanding and polishing
After 22 hrs of sanding and polishing
0 2010/07/01 23:05:27
Distributor installed to original position TDC which was difficult
Distributor installed to original position TDC which was difficult
0 2010/07/01 22:59:25
Lower intake installed
Lower intake installed
0 2010/07/01 22:59:25
Lower gaskets installed
Lower gaskets installed
0 2010/07/01 22:59:25
Mustang head gasket repair 122
Mustang head gasket repair 122
0 2010/07/01 22:58:55
Mustang head gasket repair 129
Mustang head gasket repair 129
0 2010/07/01 22:58:55
Mustang head gasket repair 125
Mustang head gasket repair 125
0 2010/07/01 22:58:55
Lower intake to blocks rear seal was not correctly seated when last installed, I cleaned the area behind the engine block which was causing oil to drip off of the clutch plate, When I installed the new cork gasket I used loctite on the lower side with motorcraft silicone sealant on top of the front and rear gaskets and to hold the gasket in place while installing the lower intake to block
Lower intake to blocks rear seal was not correctly seated when last installed, I cleaned the area behind the engine block which was causing oil to drip off of the clutch plate, When I installed the new cork gasket I used loctite on the lower side with motorcraft silicone sealant on top of the front and rear gaskets and to hold the gasket in place while installing the lower intake to block
0 2010/07/01 22:51:22
Upper cylinder heads installed after cleaning my roller lifters rods/rockers installed set and torqued to spec
Upper cylinder heads installed after cleaning my roller lifters rods/rockers installed set and torqued to spec
0 2010/07/01 22:51:22
Ford racing graphite gaskets
Ford racing graphite gaskets
0 2010/07/01 22:51:22
Lower intake after a varsol cleaning
Lower intake after a varsol cleaning
0 2010/07/01 22:48:19
Right Cylinders cleaned and lubricated with Lucas upper cylinder lubricant
Right Cylinders cleaned and lubricated with Lucas upper cylinder lubricant
0 2010/07/01 22:48:19
Lower intake removed
Lower intake removed
0 2010/07/01 22:48:19
right 1-2-3-4 cylinders
right 1-2-3-4 cylinders
0 2010/07/01 22:43:41
cleaned and painted
cleaned and painted
0 2010/07/01 22:43:41
Removed left cylinder head
Removed left cylinder head
0 2010/07/01 22:43:41
Buffed and Polished stock valve covers
Buffed and Polished stock valve covers
0 2010/07/01 22:26:49
buffed sanded and painted stock factory headers with a small spot weld reapiar paint used was krylon high temp black paint
buffed sanded and painted stock factory headers with a small spot weld reapiar paint used was krylon high temp black paint
0 2010/07/01 22:26:49
New Motorcraft spark plugs from the original dealership 130,000 km's 22 yrs later
New Motorcraft spark plugs from the original dealership 130,000 km's 22 yrs later
0 2010/07/01 22:26:49
Beggining engine teardown
Beggining engine teardown
0 2010/07/01 22:07:10
Milkshake motor oil
Milkshake motor oil
0 2010/07/01 22:07:10
New front brakes drilled rotors,hawk pads,stock calipers and hoses,bearings / nickel plated coper lines installed front and rear w/new master cylinder installed new Valvoline brake fluid added March/10
New front brakes drilled rotors,hawk pads,stock calipers and hoses,bearings / nickel plated coper lines installed front and rear w/new master cylinder installed new Valvoline brake fluid added March/10
0 2010/07/01 22:01:41
1988 Ford Mustang 5.0 HO new Mid pipe Feb/10
1988 Ford Mustang 5.0 HO new Mid pipe Feb/10
0 2010/07/01 22:01:41
1988 Ford Mustang 5.0 HO Jan/10
1988 Ford Mustang 5.0 HO Jan/10
0 2010/07/01 22:01:41
1988 Ford Mustang 5.0 HO April/10
1988 Ford Mustang 5.0 HO April/10
0 2010/07/01 21:57:42
0 2010/07/01 21:57:42
1988 Ford Mustang 5.0 HO March/10
1988 Ford Mustang 5.0 HO March/10
0 2010/07/01 21:57:42
1988 Ford Mustang LX 5.0 HO head gasket repair June/10
1988 Ford Mustang LX 5.0 HO head gasket repair June/10
0 2010/07/01 21:36:30